How Much Grout Do I Need?
Grout fills the joints, so the amount depends on how much joint there is: the tile size (small tiles mean more joints per square foot), the joint width, and the joint depth, which is the tile’s thickness. The formula:
Grout (lb per sq ft) = (L + W) ÷ (L × W) × joint width × joint depth × 144 × density
L and W are the tile’s length and width in inches, the joint width and depth are in inches, and density is in pounds per cubic inch (about 104 lb per cubic foot for sanded grout, 90 for unsanded and 110 for epoxy; typical values used across the industry). Example: 100 sq ft of 12 × 12 in tile, 3/8 in thick, with 1/8 in joints needs 6.8 lb, or 7.4 lb with 10% extra: one 25 lb bag. The same area of 2 × 2 mosaic needs 12.9 lb.
Grout Coverage Chart
Square feet covered by one bag, by tile and joint width. Joints of 1/16 in use a 10 lb bag of unsanded grout; wider joints use a 25 lb bag of sanded grout. No waste included.
| Tile (in) | 1/16" joint | 1/8" joint | 3/16" joint | 1/4" joint |
|---|---|---|---|---|
| 2 × 2 mosaic (1/4" thick) | 85 | 92 | 62 | 46 |
| 3 × 6 subway (5/16" thick) | 137 | 148 | 98 | 74 |
| 4 × 4 (1/4" thick) | 171 | 185 | 123 | 92 |
| 6 × 6 (5/16" thick) | 205 | 222 | 148 | 111 |
| 12 × 12 (3/8" thick) | 341 | 369 | 246 | 185 |
| 12 × 24 (3/8" thick) | 455 | 492 | 328 | 246 |
| 24 × 24 (3/8" thick) | 683 | 738 | 492 | 369 |
| 6 × 36 plank (3/8" thick) | 293 | 316 | 211 | 158 |
Sanded, Unsanded or Epoxy Grout?
| Type | Joint width | Best for |
|---|---|---|
| Unsanded | Under 1/8 in | Wall tile, subway, polished marble and glass (sand can scratch) |
| Sanded | 1/8 in and wider | Most floors; the sand stops wide joints shrinking and cracking |
| Epoxy | Any | Showers, kitchens, anywhere stains or water matter; costs more and sets fast |
How Much Thinset Do I Need?
Thinset coverage depends on the trowel: bigger notches leave more mortar. These ranges are for a 50 lb bag, from CUSTOM Building Products’ published coverage charts; other brands are similar, but check the bag.
| Trowel | Typical tile | Sq ft per 50 lb |
|---|---|---|
| 1/4" × 1/4" square notch | Tile up to about 8 in (mosaics on sheets, 4 × 4, 6 × 6, subway) | 85–95 |
| 1/4" × 3/8" square notch | Tile about 8–15 in (12 × 12, 6 × 24 on walls) | 60–67 |
| 1/2" × 1/2" square notch | Large format, 15 in and up (12 × 24, 24 × 24, planks) | 42–47 |
| 3/4" × 9/16" U-notch (large format) | Large and heavy tile, medium-bed mortar | 34–38 |
The trowel matters more than the bag count. The mortar should cover at least 80% of each tile’s back in dry areas and 95% in showers, wet areas and outdoors. Lift a freshly set tile now and then to check; if you see bare spots, go up a notch or back-butter. Large tiles (15 in and up) need large-format mortar and usually back-buttering, which uses roughly 20% more.
Tips for Buying and Mixing
- Buy grout from one batch and keep a little for repairs; color varies between batches.
- Mix only what you can use in about 30 minutes, and don’t add water to grout that’s stiffening.
- Joint depth is the tile thickness if the joints are cleaned out properly before grouting; leave about 1/16 in below the surface for wall tile if you prefer a flush finish with less grout.
- Seal cement grout in wet areas after it cures (usually 48–72 hours); epoxy doesn’t need sealing.
Grout and Thinset FAQ
Method and Sources
Grout: joint volume per square foot = (L + W) ÷ (L × W) × joint width × joint depth × 144, times a typical density (sanded 104, unsanded 90, epoxy 110 lb per cubic foot). Sanded or unsanded is chosen by joint width (1/8 in and wider: sanded). Thinset: coverage per 50 lb bag by trowel from CUSTOM Building Products’ technical data sheets; the bag count uses the low end of each range so you don’t run short; back-buttering adds 20% (our estimate). Mortar contact: at least 80% in dry areas and 95% in wet areas, per the same data sheets.
- CUSTOM Building Products: FlexBond thinset coverage chart
- CUSTOM Building Products: large tile mortar coverage (1/2 in and U-notch)
- CUSTOM Building Products: mortar coverage 80% dry / 95% wet
Written by K. Lynch. See our methodology. Spotted a problem? Tell us. Updates: Nov 2026, launched.