How Much Baseboard a Room Needs
Baseboard follows the floor round the room and stops at every door, so the length you need is the room’s perimeter less the door openings. The part people forget is the casing. Baseboard stops against the outside edge of the door casing, not the opening, so each door takes out its width plus a casing width and a reveal on each side. In a 12 × 14 ft room with one 32 in door and 2 1/4 in casing, that’s 36 7/8 in gone, leaving 48.9 ft of baseboard. A window doesn’t change the number at all, because baseboard runs straight underneath it.
Feet are only half the answer, because trim is sold in whole lengths and every wall wants a piece of its own. The 12 and 14 ft walls in the example each fit in a 16 ft length without a joint, and the short run beside the door shares a length with a 12 ft wall, so the room takes 4 lengths of 16 ft, plus 1 spare. Buy 8 ft lengths instead and it becomes 7 lengths with 3 scarf joints along the walls. The calculator tries every common length and picks the plan that uses the least wood, or you can lock it to what your store sells.
Inside and Outside Corners
Inside corners are where trim goes wrong. A miter looks simple, but walls are rarely exactly 90°, and as the wood shrinks the joint opens into a dark line. Coping avoids that. The first piece runs square into the corner; the second gets a 45° cut to expose its profile, then you cut along that line with a coping saw so it sits over the first piece like a puzzle. The calculator assumes coped inside corners on baseboard and works left to right along each wall, so every piece is coped on its left end and square on its right. The coped end still starts as a 45° cut, so it gets the same allowance as a miter. If you’d rather miter, untick the option and both ends of each inside corner get the allowance instead.
Outside corners are always mitered. The cut list gives each piece to its long point, the outside tip of the miter, which sits one trim thickness past the corner of the wall: 9/16 in for typical 9/16 in baseboard, 3/4 in for shoe. Cut these a hair long, hold them in place and shave to fit. Shoe or quarter round is the exception to coping: its profile is too small to cope cleanly, so the calculator miters its inside corners too. Nail shoe to the baseboard rather than the floor, so a wood floor can move under it.
Door and Window Casing Lengths
Casing is set back from the edge of the jamb so a thin strip of jamb shows. That strip is the reveal, and 3/16 in is the usual figure. Every casing length builds from it. A leg runs from the floor to the long point at the top, which is the door height plus the reveal plus the casing width. The head runs across the top to the long points at each end: the opening width, two reveals and two casing widths.
The table gives one side of a standard 80 in door with 2 1/4 in casing and a 3/16 in reveal, and the stock lengths that waste the least. Legs at 82 7/16 in just fit in a 7 ft length once you allow for the miter, which is why 7 ft casing is sold. Narrower doors can share a longer length between a leg and the head.
| Door | Each leg | Head | Buy per side |
|---|---|---|---|
| 24 × 80 in | 82 7/16 in | 28 7/8 in | 2 × 10 ft |
| 28 × 80 in | 82 7/16 in | 32 7/8 in | 2 × 10 ft |
| 30 × 80 in | 82 7/16 in | 34 7/8 in | 3 × 7 ft |
| 32 × 80 in | 82 7/16 in | 36 7/8 in | 3 × 7 ft |
| 36 × 80 in | 82 7/16 in | 40 7/8 in | 3 × 7 ft |
Windows come in two styles. Picture-frame casing runs all the way round with four mitered pieces; a 36 × 48 in window takes two pieces at 40 7/8 in and two at 52 7/8 in. The traditional stool and apron puts a flat shelf, the stool, across the bottom with a plain apron under it. The stool runs past the casing at each end by about 1 in, so for the same window it is 42 7/8 in long, and the legs stop square on top of it.
Crown Molding Angles
Crown sits at an angle between wall and ceiling, so its corners need two settings on the saw: a miter (the table swing) and a bevel (the blade tilt). They depend on the corner angle and on the crown’s spring angle, which the label gives as 52/38 or 45/45. Most crown sold at home centers is 52/38. The table gives the settings with the crown laid flat, face up, on a compound miter saw; many saws have detents at 31.6° and 33.9° for exactly this cut.
| Corner | 52/38 miter | 52/38 bevel | 45/45 miter | 45/45 bevel |
|---|---|---|---|---|
| 90° | 31.6° | 33.9° | 35.3° | 30.0° |
| 120° | 19.6° | 43.0° | 22.2° | 37.8° |
| 135° | 14.3° | 46.7° | 16.3° | 40.8° |
A 135° corner, the kind in a bay window, needs a much shallower miter of 14.3° on 52/38 crown. The alternative to all of this is cutting crown upside down and nested, with the ceiling edge on the saw table and the wall edge against the fence. Then a 90° corner is a plain 45° miter with no bevel, but the crown has to sit at its exact spring angle while you cut, so a fence stop helps. Either way, cut a short test pair from scrap first, because the direction of each cut changes with the corner and the side.
Crown runs the full perimeter of the room and ignores doors, so the example room needs 52 ft, which comes to 5 lengths of 16 ft including the spare. The cut list measures crown along its bottom edge, where it meets the wall. On outside corners, mark the piece in place rather than measuring, and the calculator allows two face widths of stock for those ends.
Buying and Fitting Trim
Primed MDF is the cheapest trim and paints well, but it swells when wet, so use primed pine or PVC in bathrooms and against floors that get mopped. Where a wall is longer than your stock, join two pieces with a scarf joint: two matching 45° cuts that overlap, glued and nailed over a stud. The calculator adds 1 in of overlap for each one. Nail baseboard and casing with 2 in 18-gauge brads, two at each stud; the example room’s baseboard and casing take about 160.
Baseboard and Trim FAQ
How This Calculator Works
Each wall is a run of trim with an inside corner, outside corner, or a stop at a door or open end at each side. Baseboard and shoe have each door cut out, widened by a casing width and a reveal on each side; crown follows the walls in full. Long points, allowances and casing lengths follow the rules described above, and each stock length is credited with one miter triangle, because the first cut on a length uses the factory end. Runs longer than the stock are split with 1 in scarf overlaps. Pieces are packed with a 1/8 in saw cut, trying several orders and keeping the plan with the fewest lengths, and we check the packing against an exhaustive search on small jobs. Crown settings use miter = atan(cos K ÷ tan(A/2)) and bevel = asin(sin K × sin(A/2)), where A is the corner angle and K is 52° or 45°. The nail count is our own rule.
- Fine Homebuilding: 8 basic rules to master trim carpentry (3/16 in reveal)
- Fine Homebuilding: window trim with a stool and apron
- Ryobi TS1340 manual: cutting 52/38 crown laid flat (31.62° miter, 33.85° bevel)
- WOODWEB: crown moulding miter and bevel angle chart
Written by Kris Lynch. See our methodology. Spotted a problem? Tell us. Updates: Nov 2026, launched.