How to Use Your Marks
The marks table gives the left edge of every batten measured from the left corner. For the 12 ft example wall that’s 0, 14 1/8, 28 5/16, 42 7/16, 56 5/8 in, and so on to 141 1/2 in. Measuring every mark from the corner, rather than from the batten before it, stops small errors from piling up across the wall.
- Mark each left edge along the top of the baseboard with a pencil and tape measure hooked on the corner.
- Cut one spacer block to the gap (11 5/8 in for the example) from a scrap of batten.
- Fit the corner battens first, then work across, using the spacer block to hold each batten while the adhesive grabs.
- Every third batten, check it against its pencil mark and check plumb with a level. If the wall leans, follow the level, not the corner.
The calculator also tells you how far a spacer block alone would drift. On the example wall, rounding 11.65 in to 11 5/8 in adds up to 1/4 in over ten gaps, which is enough to see at the far corner.
Batten Spacing Chart
Each cell shows the number of battens and the exact gap for a batten in both corners. Pick the column closest to the look you want, then put your own wall width into the calculator for the marks.
| Wall | 1x2 (1 1/2 in) | 1x3 (2 1/2 in) | 1x4 (3 1/2 in) | |||
|---|---|---|---|---|---|---|
| ~12 in gap | ~16 in gap | ~12 in gap | ~16 in gap | ~12 in gap | ~16 in gap | |
| 6 ft | 6 · 12 5/8 | 5 · 16 1/8 | 6 · 11 3/8 | 5 · 14 7/8 | 5 · 13 5/8 | 5 · 13 5/8 |
| 8 ft | 8 · 12 | 6 · 17 3/8 | 7 · 13 1/16 | 6 · 16 3/16 | 7 · 11 15/16 | 6 · 15 |
| 10 ft | 10 · 11 11/16 | 8 · 15 7/16 | 9 · 12 3/16 | 7 · 17 1/16 | 9 · 11 1/16 | 7 · 15 15/16 |
| 12 ft | 12 · 11 7/16 | 9 · 16 5/16 | 11 · 11 5/8 | 9 · 15 3/16 | 10 · 12 1/8 | 8 · 16 9/16 |
| 14 ft | 13 · 12 3/8 | 11 · 15 1/8 | 12 · 12 9/16 | 10 · 15 7/8 | 12 · 11 7/16 | 9 · 17 1/16 |
| 16 ft | 15 · 12 1/8 | 12 · 15 13/16 | 14 · 12 1/16 | 11 · 16 7/16 | 13 · 12 3/16 | 11 · 15 3/8 |
| 18 ft | 17 · 11 15/16 | 13 · 16 3/8 | 16 · 11 3/4 | 13 · 15 5/16 | 15 · 11 11/16 | 12 · 15 13/16 |
| 20 ft | 19 · 11 3/4 | 15 · 15 9/16 | 17 · 12 3/8 | 14 · 15 3/4 | 16 · 12 1/4 | 13 · 16 3/16 |
Battens · exact gap in inches, rounded to 1/16. Wall widths between rows give different gaps, so use the calculator for yours.
How Tall Should Board and Batten Go?
A third of the wall reads as wainscoting, two thirds is the usual height for an accent wall, and full height suits bedrooms and entries where there’s no furniture to hide the lower half. The height you pick also decides which board length wastes least. With a 3 1/2 in baseboard and a 1x4 top rail, a two-thirds wall under an 8 ft ceiling needs 57 in battens. An 8 ft board gets one of those and a 10 ft board gets two. If you’d rather have boxes of moulding under a chair rail than battens, the wainscoting calculator lays those out wall by wall.
| Ceiling · height | Top of trim | Batten length | Per 8 ft board | Per 10 ft | Per 12 ft |
|---|---|---|---|---|---|
| 8 ft · 1/3 | 32 in | 25 in | 3 | 4 | 5 |
| 8 ft · 1/2 | 48 in | 41 in | 2 | 2 | 3 |
| 8 ft · 2/3 | 64 in | 57 in | 1 | 2 | 2 |
| 8 ft · Full | 96 in | 89 in | 1 | 1 | 1 |
| 9 ft · 1/3 | 36 in | 29 in | 3 | 4 | 4 |
| 9 ft · 1/2 | 54 in | 47 in | 2 | 2 | 3 |
| 9 ft · 2/3 | 72 in | 65 in | 1 | 1 | 2 |
| 9 ft · Full | 108 in | 101 in | 0 | 1 | 1 |
| 10 ft · 1/3 | 40 in | 33 in | 2 | 3 | 4 |
| 10 ft · 1/2 | 60 in | 53 in | 1 | 2 | 2 |
| 10 ft · 2/3 | 80 in | 73 in | 1 | 1 | 1 |
| 10 ft · Full | 120 in | 113 in | 0 | 1 | 1 |
Assumes a 3 1/2 in baseboard, a 3 1/2 in top rail and a 1/8 in saw cut between pieces. Bold marks the length that wastes least per foot.
Gap or On-Centre: Which Number Do You Need?
The gap is the clear space between two battens, and it’s the size of your spacer block. On centre runs from the middle of one batten to the middle of the next, so it is always the gap plus one batten width: 11 5/8 + 2 1/2 = 14 1/8 in on the example wall. Mixing the two up is the most common reason a wall ends with a narrow gap in the last bay.
Battens Around Outlets, Switches and Windows
Add your outlets and switches in the calculator and it checks whether any batten lands on a cover plate, allowing 1/2 in of clearance on each side. When one does, it tries one to four battens more or fewer and offers the closest spacing that misses every plate, which is nearly always better than notching.
If you do notch a batten or cover a wall in shiplap, the electrical box has to reach the new surface. The National Electrical Code (314.20) lets a box sit up to 1/4 in back from drywall, but in a wall finished with wood the box or a listed extender must extend to, or project from, the finished surface. Battens that only run beside a box don’t change anything. A box extender is a few dollars at a hardware store; anything beyond fitting one is a job for a licensed electrician.
Windows and doors work differently. Battens stop at the trim and continue above and below it, and the calculator cuts them to length around each opening rather than counting full-height pieces you’d only trim down.
Which Board Length to Buy
Battens are rarely a neat fraction of 8 ft, so the board length matters more than people expect. The example wall needs eleven 57 in battens. From 8 ft boards you get one batten each, so that’s 11 boards and 88 ft of wood. From 10 ft boards you get two each, so 6 boards and 60 ft. The 10 ft option saves 28 ft of 1x3.
With “Auto” selected, the calculator tries 8, 10, 12 and 16 ft boards for every size and picks the one that buys the least wood, then shows each board’s cuts in the cut list. On the example it also takes the 12 ft top rail from a single board, so there’s no joint to hide. If you set 8 ft boards, joints in the top rail are placed on a batten centre, where the next batten covers them.
Batten Materials
Primed MDF is the cheapest and smoothest option, and it cuts cleanly, but it dents easily and swells at any cut end that gets wet. Primed finger-joint pine costs a little more, holds nails better and tolerates a bathroom once it’s painted. Poplar is a hardwood that stays straight and takes a crisp painted edge, which is why finish carpenters like it. PVC trim costs the most but never rots, so it’s the choice for showers, mudrooms and outside.
All of these are sold by the piece or by the linear foot. The board foot calculator is for rough-sawn hardwood, which is priced by volume instead.
Whatever you use, the actual sizes are smaller than the names: a 1x3 is 3/4 × 2 1/2 in, a 1x4 is 3/4 × 3 1/2 in and a 1x6 is 3/4 × 5 1/2 in, following the American Softwood Lumber Standard. The calculator uses the actual widths.
Board and Batten Siding
Outside, board and batten is either wide boards with a gap between them or 4 × 8 ft siding panels with battens on top. With boards, a batten covers every gap, and the gap (often 1/2 in) gives the wood room to move. With panels, battens go at 12, 16 or 24 in on centre so they nail into studs, and those spacings all land on the 4 ft panel seams. The Siding tab handles both, rips the last board when the width doesn’t divide evenly, and balances the two end boards if the last one would be narrow. Follow the siding maker’s nailing schedule; this calculator does the layout and quantities only.
Shiplap: How Many Boards You Need
Shiplap is counted in rows, not square feet. Each row covers the board’s exposure, which is its actual width minus the overlap, so a 1x6 with a 3/8 in overlap covers 5 1/8 in. Divide the wall height by that and round up:
Rows = wall height ÷ exposure, rounded up · last row = height − (rows − 1) × exposure
An 8 ft wall takes 19 rows, and the top row is ripped to 3 3/4 in. On a 12 ft wide wall, 12 ft boards cover a row each (19 boards, no joints). With 8 ft boards it takes 29, because each row needs one and a half boards and the offcuts start the next row. The calculator keeps joints in neighbouring rows at least 16 in apart and never leaves a piece shorter than 12 in. If the last row comes out under half a board, tick “balance the edge rows” to split the difference between the top and bottom rows.
Shiplap From Plywood Strips
Ripping 4 × 8 sheets of 1/4 in plywood into strips is the cheapest way to get the shiplap look. A 6 in strip plus a 1/8 in saw cut means each sheet gives 7 full strips. The example 12 × 8 ft wall takes 16 rows with a 4 1/8 in top row, which is 25 strips, or 4 sheets. Lightly sand the cut edges, paint the wall behind first if the gaps will show, and use a nickel or a 1/8 in tile spacer between rows.
Board and Batten FAQ
How This Calculator Works
Even spacing comes from gap = (wall width − battens × batten width) ÷ number of gaps, where the number of gaps is one less than the battens with a batten in both corners, equal to it with one corner, and one more with none. The batten count is the one that brings the gap closest to your target. Every mark is worked out from the left corner at full precision and only then rounded to the nearest 1/16 in.
The cut list packs pieces into boards longest-first, allowing a 1/8 in saw cut, and we check it against an exhaustive search on small jobs. Adhesive uses Loctite PL 375’s published coverage of 30.6 ft of 1/4 in bead per 10 oz tube; other adhesives differ. The nail count is our own rule of one brad every 8 in plus one per piece. Spacing ranges come from HGTV and Inch Calculator.
- Loctite PL 375 technical data sheet (coverage per tube)
- EC&M: NEC 314.20 requirements for flush-mounted boxes
- HGTV: How to install a board and batten accent wall
Written by Kris Lynch. See our methodology. Spotted a problem? Tell us. Updates: Nov 2026, launched.