Skip to calculator

Carpet Calculator

A 12 × 14 ft bedroom on a 12 ft roll takes 20.0 sq yd of carpet for 18.7 sq yd of floor. Add your rooms and stairs below for the roll plan, seams and cost.

Carpet calculator

Roll width

Most carpet comes 12 ft wide; some styles also come 15 ft. Type lengths the way you’d say them: 14, 11' 6" or 11.5.

Stairs
Enter a room to see how much carpet to buy.

How Much Carpet a Room Needs

Carpet isn’t sold to fit your floor area. It comes off a roll, usually 12 ft wide, and you pay for every foot of length cut off it, full width. So the question is how many strips of roll the room takes and how long each one is. A 12 × 14 ft bedroom fits in one strip, 14 ft long plus about 3 in at each end for trimming to the wall. The store cuts 15 ft off the roll: 20.0 sq yd for 18.7 sq yd of floor.

That’s why multiplying length by width and adding 10% so often gives the wrong answer. The waste depends on how the room’s width fits the roll, not on a percentage. The table shows what you buy for some common room sizes.

RoomFloor (sq yd)Buy on a 12 ft rollBuy on a 15 ft roll
10 × 10 ft11.114.718.3
10 × 12 ft13.314.718.3
12 × 12 ft16.017.321.7
12 × 14 ft18.720.021.7
12 × 16 ft21.322.728.3
13 × 14 ft20.236.023.3
14 × 16 ft24.938.728.3
15 × 20 ft33.341.335.0

Square yards to buy, with 3 in of trim at each end and the length rounded up to a whole foot. The calculator picks the direction that uses less carpet.

Roll Width, Seams and Waste

A room wider than the roll in both directions needs a second strip, and that is where the waste comes from. Make the 12 × 14 ft bedroom 13 ft wide and it no longer fits one strip either way. The cheaper layout runs the strips across the 13 ft side: a full 12 ft strip and a 2 ft fill strip, each 13 ft 6 in long. The fill still needs its own length of roll, so you buy 36.0 sq yd for 20.2 sq yd of floor. On a 15 ft roll the same room is one piece and 23.3 sq yd. When you carpet several rooms at once, a narrow fill from one room can often be cut beside another room’s piece, which is why the calculator plans every room on one roll.

A 13 by 14 ft room on a 12 ft rollThe room drawn with strips running across its 13 ft side: one full 12 ft wide strip and a 2 ft wide fill strip, with a seam between them. Beside it, the roll: the full strip takes one length, and the 2 ft fill takes a second length on its own, leaving the rest of that width as offcut. 12 ft strip2 ft fill 14 ft across, 13 ft deep length 12 ft filloffcut two 13 ft 6 in lengths off a 12 ft roll
A room just over the roll width needs a fill strip, and that strip takes a whole length of roll.

Where the seams go matters as much as how many there are. Atlas Carpet Mills’ installation instructions say to avoid seams that run into doorways and entrances, where they take the most wear. They also say every piece must lie with its pile in the same direction, because carpet laid two ways looks like two shades. If you add each room’s main doorway, the calculator warns when a seam would run into it, and it keeps the pile the same way in every room unless you turn that off.

What Carpet Costs Installed

HomeGuide puts installed carpet at $2 to $8 per sq ft, made up of the carpet itself at $1.00 to $4.50, pad at $0.25 to $1.00, and labor at $0.50 to $1.50. Taking up old carpet and pad adds $0.70 to $1.60. Across those ranges, the 12 × 14 ft bedroom comes to roughly $430 to $1,520 with new pad and removal, priced on the 20 sq yd you buy rather than the floor area.

Stairs are priced per step. Angi puts carpeting stairs at $11 to $26 a step more than carpeting floors, because every step is cut and fitted by hand, and HomeAdvisor lists stair carpet removal at about $7.50 to $10.50 a step. Most installers also have a minimum charge, so a single small room costs more per yard than a whole floor. The calculator leaves the prices blank so you can type the figures from your own quotes; the typical ranges sit beside each box.

Carpeting Stairs

Measure the tread from the back of the step over the front edge (the nose), and the riser from the top of one tread to the next. Each step takes tread plus riser, and a Hollywood-style install, where the carpet wraps tightly under the nose, needs about 1 in more per step. A waterfall install drops straight from the nose and needs nothing extra. Add 2 in to the stair width, because the installer folds about an inch under at each side.

The pile has to run down the stairs, so a flight of 13 steps is about 20 ft of carpet in one direction. That rarely comes from one long piece. Installers cut it in sections of a few steps and join them in the back corner of a step, where the seam hides, which lets the sections sit side by side on the roll. The calculator does the same, and a 36 in flight of 13 steps comes from 9 ft of a 12 ft roll.

Pad, Tack Strip and Seams

Pad goes under the whole floor and on each stair tread. It’s sold by the square yard and its seams don’t show, so it needs no roll plan. Replace it with the carpet: old pad is crushed, and some warranties require new pad. Tack strip, the thin board with angled pins that grips the carpet edge, runs round every wall and is sold in 4 ft pieces; the 12 × 14 ft bedroom takes 13. Seams are joined with hot-melt seam tape along their full length, which the calculator adds up for you.

Carpet FAQ

The floor is 16 sq yd, but you buy 17.3 sq yd: one 13 ft length off a 12 ft roll, because each end needs about 3 in for trimming and stores cut in whole feet. On a 15 ft roll it would be more, since you pay for the full width.

HomeGuide puts installed carpet at $2 to $8 per sq ft, so roughly $2,000 to $8,000 for 1,000 sq ft of floor. Add $700 to $1,600 to take up the old carpet and pad, and expect to buy more carpet than the floor area once each room is laid out in roll widths.

With 10 in treads, 7 1/2 in risers and a 36 in wide flight, each step takes 18.5 in of carpet with a Hollywood wrap, about 20.0 ft in all. Cut in 3 sections laid side by side, that comes from 9 ft of a 12 ft roll, or 12.0 sq yd.

Usually, yes. Old pad is compressed and often stained, and some carpet warranties require new pad. It is a small part of the job: HomeGuide lists pad at $0.25 to $1.00 per sq ft, against $1.00 to $4.50 for the carpet itself.

Both. Stores often quote carpet per square yard and installers per square foot. A square yard is 9 sq ft, so $27 per sq yd is $3 per sq ft. Check which unit each quote uses before comparing them.

How This Calculator Works

Each room is split into strips running with the pile, as many as the width across the pile needs at the roll width. Each strip is the room’s length plus 3 in at each end, and a narrow fill strip is cut 1 in wider than it needs to be for trimming the seam. A closet or bump-out gets its own pieces with the pile the same way. The calculator tries each room both ways round and keeps the direction that uses the least roll, with one direction for every room unless you turn that off. Stairs take tread plus riser per step, plus 1 in for a Hollywood wrap, at the stair width plus 2 in, split into sections where that saves roll. Every piece is then packed onto one roll, side by side across the width and end to end along it, trying several orders and keeping the shortest. We test that packing against an exhaustive search on small jobs. The length is rounded up to a whole foot. Tack strip is the room perimeters plus one strip per step, in 4 ft pieces.

Written by Kris Lynch. See our methodology. Spotted a problem? Tell us. Updates: Nov 2026, launched.

Related Calculators