Skip to calculator

Countertop Square Footage Calculator

An L-shaped counter with 10 ft and 8 ft legs plus a 6 ft island is 52.7 sq ft, about 2 standard quartz slabs. Enter your pieces below for square feet, slabs, edges and cost.

Countertop calculator

Enter each separate piece of countertop. Measure every leg along the wall, from end to end, and the depth from the wall to the front edge (usually 25 1/2 in; bathroom vanities about 22 in).

Piece 1
Piece 2

All four edges of an island are finished.

Slab size, cooktop and backsplash
Prices (optional)

Enter the length of each piece.

Measuring Pieces, Corners and Islands

Split the countertop into pieces you can treat as rectangles: each straight run, each L or U, and each island or peninsula. Measure every leg along the wall from end to end, and the depth from the wall to the front edge, then multiply and divide by 144 for square feet.

straight run: length × depth ÷ 144
L-shape: (leg 1 + leg 2 − depth) × depth ÷ 144
U-shape: (leg 1 + leg 2 + leg 3 − 2 × depth) × depth ÷ 144

Corners are where most measurements go wrong. Measure both legs of an L along the wall and the corner square sits inside both, so it has to come off once. An L with 10 ft and 8 ft legs at 25 1/2 in deep is (120 + 96 − 25 1/2) × 25 1/2 = 4,857 3/4 sq in, or 33.7 sq ft. A 6 ft island 38 in deep adds 19 sq ft, for 52.7 sq ft in all. Leave the sink and cooktop in: the opening is cut from a piece you still pay for, and the cut-out is charged on top. A stone backsplash strip, if you’re having one, is its height times the length along the wall.

Will It Fit on One Slab?

Square footage alone doesn’t tell you how much stone to buy, because every piece has to be cut whole from a slab. Caesarstone’s standard quartz slab is 120 × 56 1/2 in and its jumbo is 131 1/2 × 64 1/2 in; granite varies from stone to stone. A standard slab holds two 25 1/2 in runs side by side, but a 38 in island takes the slab’s full width on its own, and the leftover strip is often too narrow to use. That’s why the 52.7 sq ft example needs 2 standard slabs (2 jumbo) even though one slab holds about 47 sq ft. Runs longer than a slab need a seam. Treat the count as an estimate, since your fabricator plans the real layout around veining, seams and edges.

What Countertops Cost per Square Foot

Material sets most of the price. These are Fixr’s cost-per-square-foot ranges, updated January 2026, applied to the 52.7 sq ft example. Fixr doesn’t say whether every figure includes installation, so check what each quote covers.

MaterialPer sq ft52.7 sq ft example
Quartz$50 to $200$2,640 to $10,550
Granite$40 to $150$2,110 to $7,910
Marble$50 to $200$2,640 to $10,550
Quartzite$60 to $200$3,160 to $10,550
Solid surface (Corian)$40 to $100$2,110 to $5,270
Concrete$50 to $120$2,640 to $6,330
Butcher block$40 to $100$2,110 to $5,270
Laminate$15 to $60$790 to $3,160

Some costs sit on top of the square footage. Fixr puts extra cut-outs for sinks, faucets and cooktops at $100 to $200 each, edge profiles beyond eased or square at $10 to $40 per linear foot, and taking out the old countertops at $50 to $300 in total. Type your own prices into the calculator and it adds the cut-outs and removal for you.

Standard Depths and Overhangs

If you’re planning new cabinets as well, kitchen countertops are usually 25 1/2 in deep: a 24 in base cabinet plus a 1 1/2 in overhang at the front. Islands vary more because seating needs knee room, about 15 in of overhang for counter-height stools, at least 12 in for bar-height stools and about 18 in for a table-height chair. Large overhangs need brackets or steel supports, especially under heavy stone. Bathroom vanity tops are shallower, usually 19 to 22 in.

Countertop Questions

No. Measure the full top, including the sink and cooktop, because the opening is cut from a piece you still pay for. Fabricators usually charge for each cut-out on top: Fixr puts extra openings at $100 to $200 each. So a 52.7 sq ft kitchen with one sink is priced as 52.7 sq ft plus one cut-out.

About 30 sq ft, the average Angi gives, though it varies a lot with the kitchen. A single 10 ft run at 25 1/2 in deep is about 21 sq ft, an L-shape with 10 ft and 8 ft legs is about 33.7 sq ft, and adding a 6 ft island takes it to about 52.7 sq ft.

About 25 1/2 in: a 24 in base cabinet plus a 1 1/2 in overhang at the front. Islands with seating are deeper, because a counter-height stool needs about 15 in of knee space and a bar-height stool at least 12 in. Bathroom vanity tops are shallower, usually 19 to 22 in.

About $1,500 to $6,000, using Fixr’s range of $50 to $200 per sq ft for quartz, before cut-outs, fancy edges or removing the old tops. Fixr puts designer colours and thick slabs at the top end.

Often 1 for an average 30 sq ft kitchen, more with an island. A standard quartz slab is about 120 × 56 1/2 in, roughly 47 sq ft, but pieces have to fit whole, so you rarely use it all. The 52.7 sq ft example needs 2 standard slabs. Your fabricator plans the real layout around seams and veining.

How the numbers are worked out: each piece is its length times its depth, with the corner square counted once in an L or U and nothing taken off for sinks or cooktops. The finished edge is every front edge plus open ends, and all four sides of an island. For slabs, pieces are cut into strips no longer than a slab and packed deepest first. We test the engine on tens of thousands of random kitchens to check that every strip fits and the areas always add up. I rebuilt my own kitchen in 2022, which is part of why the pages here show their working.

Written and checked by Kris Lynch. Not reviewed by a licensed professional. See our methodology. Spotted a problem? Tell us. Updates: Nov 2026, launched.

Related Calculators