Skip to calculator

Backsplash Calculator

A 10 ft and a 6 ft run at 18 in high is 24 sq ft, or 212 3 × 6 in subway tiles with 10% for cuts. Enter your runs below for square feet, tiles or boxes, the cut row, trim, grout and adhesive.

Backsplash calculator

Enter each straight stretch of counter as a run. Measure the height from the counter to the underside of the upper cabinets, usually 18 in.

Run 1
Run 2
Range, windows and tile details

Windows

Enter the length and height of each run.

What Size Is Your Backsplash?

Treat each straight stretch of counter as its own run, ending at a corner, the fridge or the end of the cabinets. Measure its length along the wall and its height from the counter to the underside of the upper cabinets. Standard kitchens leave 18 in, but older and custom kitchens vary, so check both ends and use the bigger figure. Length times height, added up for every run and divided by 144 if you worked in inches, is your square footage: a 10 ft run and a 6 ft run at 18 in high come to 3,456 sq in, or 24 sq ft.

The range and any window are where people get it wrong. Tiling up to the hood adds the extra height behind the range: a 30 in wide range with the hood 30 in above the counter adds 30 × 12 = 360 sq in, or 2 1/2 sq ft. A window inside the backsplash height takes area away: a 36 in window with its sill 12 in up removes 36 × 6 = 216 sq in, or 1 1/2 sq ft. With both, the example becomes 25 sq ft. Outlets and switches stay in, because you still cut tile around them and the offcuts are rarely usable.

The Row Under the Cabinets

Tile rows rarely fit the height exactly, and the leftover strip is what makes a backsplash look professional or not. With 3 × 6 in subway laid flat and 1/16 in joints, each row takes 3 1/16 in, so 18 in holds 5 full rows with a 2 11/16 in strip left over. Widen the joints to 1/8 in and the strip shrinks to 2 3/8 in. Most people put that cut row at the top, where the cabinet edge hides it, and start full tiles on the counter.

The one to avoid is a sliver, a strip under about a third of a tile tall. It looks like a mistake and tends to snap as you cut it. If the calculator flags one, cut a partial row at the counter as well and split the difference, or try a different joint width. The drawing in the full plan shows where the cut lands on your first run. Open ends, and runs with no upper cabinets, leave a raw tile edge to finish with metal trim, bullnose tile or a pencil liner; the calculator counts that edge length and the trim pieces at the length you set.

Tiles, Boxes and the Extra for Cuts

Add 10% for a straight or brick layout and 15% for herringbone or diagonal, which waste more at every edge. A backsplash has a lot of edges for its size, so don’t go below 10%. The 24 sq ft example becomes 26.4 sq ft to buy: 212 subway tiles laid straight, 221 in herringbone, 80 of the larger 4 × 12 in, or 27 mosaic sheets of about 1 sq ft. Box sizes vary by product, so type the square feet per box from the label to get a box count, and buy every box from the same batch, since colour shifts between lot numbers.

The adhesive and grout figures in the full plan are smaller than most people expect. The example takes 1 gallon pail of mastic or premixed thin-set and 1 quart of grout, because a backsplash is only a couple of dozen square feet.

Backsplash Questions

Most kitchens fall between about 20 and 35 sq ft. The standard height between the counter and the upper cabinets is 18 in, so each foot of counter adds 1 1/2 sq ft: a small L-shaped kitchen with 8 ft and 4 ft runs is 18 sq ft, and a bigger one with 12, 8 and 5 ft runs is 37.5 sq ft. A range wall tiled up to the hood adds a few more.

Eight. One 3 × 6 in tile covers 18 sq in, and a square foot is 144 sq in. Grout joints take up a little room, so the true figure is slightly under 8, which the 10% for cuts covers: 24 sq ft of backsplash needs 212 tiles.

Take off windows, not outlets. A window that sits inside the backsplash height leaves a real gap: a 36 in window with its sill 12 in above the counter removes 1 1/2 sq ft from an 18 in high run. Outlets and switches are small, and you still cut tile around them, so leave them in.

Less than most people buy. For 24 sq ft of 3 × 6 in subway tile with 1/16 in joints, the joints hold about 37 cu in of grout, so a single quart of premixed grout is plenty. Adhesive goes on with a 3/16 in V-notch trowel at about 40 sq ft per gallon, so one gallon pail covers it.

Where the numbers come from: tile counts use square feet plus 10% (15% for herringbone or diagonal, the low end of Inch Calculator’s 15 to 20%) divided by one tile’s face. Adhesive uses the low end of the label coverage for premixed products: 40 sq ft per gallon with a 3/16 in V-notch for tile up to 6 in, 20 with a 1/4 in square-notch up to 12 in, and 14 with 1/4 × 3/8 in above that. Grout is the joint volume from the standard formula plus 10%. We test the engine on thousands of random kitchens to check that tile counts always cover the area and the rows always add up to the height.

Written and checked by Kris Lynch. Not reviewed by a licensed professional. See our methodology. Spotted a problem? Tell us. Updates: Nov 2026, launched.

Related Calculators