Skip to calculator

Siding Calculator

A 40 × 30 ft single-story house with two gables needs about 15 squares of vinyl siding, or 204 fiber cement planks 8 1/4 in wide. Enter your house below for squares, planks, trim and cost.

Siding calculator

Outside wall to outside wall, and from the bottom of the siding to the eaves (about 18 ft for two stories). For an L-shaped house, add the extra wall under “Gables, other walls and waste”.

Gables, other walls and waste

Gables sit on the width walls. Measure a gable’s height from the eaves line to the peak if you know it.

Without measured openings, windows count as 3 × 5 ft, doors 3 ft × 6 ft 8 in and garage doors 16 × 7 ft.

Prices (optional)
Enter the house’s length and width.

Measure the Walls, Then the Gables

Siding covers walls, so the number that matters is wall area, not the floor area on your house plans. Measure the house’s length and width outside, add them and double it for the perimeter, then multiply by the wall height from the bottom of the siding to the eaves. The 40 × 30 ft example house has 140 ft of wall 9 ft high, or 1,260 sq ft.

Gables are the triangles under a pitched roof, and they’re easy to forget. Each one is its width times its height, halved. If you can’t get up to measure the height, the roof pitch gives it: a 30 ft wide end at a 6/12 pitch rises 6 in for every foot to the middle, so 7 1/2 ft. Two of those add 225 sq ft. Take off the windows and doors (190 sq ft for 10 windows and 2 doors at typical sizes) and the example has 1,295 sq ft to side. Adding 10% for cuts and offcuts, as Kaycan’s estimator and Lowe’s both suggest, makes 1,425 sq ft.

Squares, Planks and Pieces

Vinyl is sold and quoted by the square, 100 sq ft of wall, so the example needs 15 squares. Panels per square depend on the profile, and the carton gives the figure if you want a panel count.

Fiber cement and wood lap siding are counted in boards, and the number turns on the exposure, the part of each board left showing once the next one overlaps it. A 12 ft board covers its exposure times 12 ft, so an 8 1/4 in HardiePlank showing 7 in covers 7 sq ft. James Hardie’s coverage chart works the same way, from 25 planks a square for its narrowest board to 9 for its widest. On the example, 7 1/4 in planks would take 238, 8 1/4 in planks 204 and 9 1/4 in planks 179: an inch of exposure moves the count by about 15%.

The Trim Most Estimates Forget

Siding doesn’t finish itself. Vinyl needs a starter strip along the bottom, a post at every outside corner and J-channel to take the cut ends round windows, doors, rakes and eaves. Ply Gem’s estimating guide gives rules of thumb per square: 0.8 starter strips, 0.2 outside corner posts and 2 pieces of J-channel. Those suit an average house, but trim follows the house’s shape, not its area, so this calculator measures it.

On the example, the measured figures are 14 starter strips for the 140 ft perimeter in Kaycan’s 10 ft lengths, 4 corner posts (one per corner, since the walls are under 10 ft) and 340 ft of J-channel, or 27 pieces of 12.6 ft. Ply Gem’s factors give 12, 3 and 29, close, but short on starter strip and corners, the kind of gap that sends you back to the store. Ply Gem also suggests about 1/3 lb of nails per square, 5 lb here.

What New Siding Costs

Fixr puts vinyl siding at $3 to $12 per sq ft installed, with labor alone at $2 to $5, and fiber cement at $5 to $14 installed, with labor at $2 to $8 per sq ft and planks at $4 to $14 (both guides updated January 2026). On the example’s 1,295 sq ft of wall, that’s about $3,880 to $15,540 in vinyl and $6,480 to $18,130 in fiber cement. Taking off and hauling away the old siding adds $1,000 to $2,500 if the contractor doesn’t include it. Fiber cement comes primed, pre-painted or dyed, and primed boards still need painting. Type your own quotes into the calculator to see the total.

Siding Questions

About 17 squares on one story or 21 on two, because siding covers the walls, not the floor. A one-story 50 × 30 ft house with 9 ft walls, two 6/12 gables, 10 windows and 2 doors has 1,475 sq ft of wall, or 17 squares with 10% waste. The same 1,500 sq ft on two stories, 30 × 25 ft with 18 ft walls and 14 windows, has 1,886 sq ft of wall and needs 21 squares.

About 14 of the 8 1/4 in planks, which show 7 in each, and 17 of the 7 1/4 in planks at 6 in. James Hardie’s coverage chart runs from 25 planks a square for the narrow 5 1/4 in board down to 9 for the 12 in board, all in 12 ft lengths and before waste.

It depends whose method you follow, and the two give similar totals. Kaycan’s estimator takes every window and door off and then adds 10% for waste. JLC’s field guide leaves them in as the waste allowance, and only deducts 75% of the openings when they add up to more than 50 sq ft. This calculator takes them off and adds the 10%.

Ply Gem’s rule of thumb is 2 pieces per square, so about 29 pieces for a 15 square house. Measuring it is better: J-channel goes round every window and door, up the gable rakes and under the eaves, and on the example house that’s 340 ft, or 27 pieces of 12.6 ft.

The order of the sums follows Kaycan’s vinyl siding estimator: walls and gables, less openings, plus 10% waste, then squares. Plank counts use exposure × length, which matches James Hardie’s coverage chart, and the trim is measured from the house with Kaycan’s piece lengths and set beside Ply Gem’s per-square factors. We test the engine against every row of the Hardie chart and on tens of thousands of random houses to check that the trim it lists is never short of the length it measures.

Written and checked by Kris Lynch. Not reviewed by a licensed professional. See our methodology. Spotted a problem? Tell us. Updates: Nov 2026, launched.

Related Calculators